Seite 3 von 3

Re: Ἀδάμας de France !

Verfasst: Sonntag 26. März 2017, 19:26
von trifi70
What about voltage? Did you checked this point? Both modules need 6V! Do you use original HGN5001 power plug?

Re: Ἀδάμας de France !

Verfasst: Sonntag 26. März 2017, 20:27
von Diamant
• Yes it is the right adapter HGN 5001.. ;)

Mephisto ~ AC/DC ADAPTER
Input : 220V~/50Hz/6VA
Output : 8V=/250mA/2W
Type : FW 3199 - IP20
Made in Germany - 140/E
? 125°C etc.....

Re: Ἀδάμας de France !

Verfasst: Sonntag 26. März 2017, 20:38
von trifi70
And what "arrives" at the module? 6V inside?

Did you test the display from MM II together with Mirage module? This is possible and extern display should show the content of Mirage display. If not, there is something wrong with the bus on "backplane" or with output connector of Mirage module.

Re: Ἀδάμας de France !

Verfasst: Sonntag 26. März 2017, 23:57
von Diamant
Here are the tests :

¹ - Mephisto Mirage + Modul MM II
Test_Plateau_Mephisto_Exclusive.jpg
Test_Plateau_Mephisto_Exclusive.jpg (121.44 KiB) 815 mal betrachtet
Nothing is happening..
That the appearance of hieroglyphics :mrgreen: in place of PLAY ?


² - Modul MM II ~ PLAY ~
Test_Plateau_Mephisto_Exclusive (1).jpg
Test_Plateau_Mephisto_Exclusive (1).jpg (68.36 KiB) 815 mal betrachtet
Flashing LED's ... Pawn B7 and Bishop C8 ?!

Unable to launch a game !

Re: Ἀδάμας de France !

Verfasst: Montag 27. März 2017, 09:48
von trifi70
Oh, don't use two PROGRAM modules together (at same time) like shown on first picture... What I suggested: MM II DISPLAY + Mirage. So you should have 2 displays with identical content.

But, I think I know what the problem is: the module scans the reeds on the chess board. At start of a new game there should be placed 32 pieces on the board. If not some LEDs will flash, mostly on two lines side by side. And this is also the case when one ore more of the reeds are faulty.

Check the reeds. Use Mirage module. Use one piece only! Start a new game (on/off). Put piece on a2 and remove piece. What will happen? LED should flash. Put piece on a3 and remove. Mirage should "think" some time and answer with e2e4 or so. Put piece on b2, then b3. Mirage should answer.

You can test all fields as following: put piece on e2 or so. Remove piece and put on the field to test. Mirage should "beep" and say something like "err". Take back the "move" and test next field.

You should test all 64 fields and replace the faulty reeds.

Re: Ἀδάμας de France !

Verfasst: Montag 27. März 2017, 12:47
von Diamant
Test_Plateau_Mephisto_Exclusive (2).jpg
Test_Plateau_Mephisto_Exclusive (2).jpg (98.75 KiB) 804 mal betrachtet
On the three modules "¹ - Mirage + ² - DISPLAY + ³ MM II"...
the PLAY screen does not appear.

Test_Plateau_Mephisto_Exclusive (3).jpg
Test_Plateau_Mephisto_Exclusive (3).jpg (94.82 KiB) 804 mal betrachtet
Nothing happens except the flashing of the LED of the black pawn in B7.